ISL datasheet, ISL circuit, ISL data sheet: INTERSIL – High- Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers . ISL Datasheet, ISL PDF, ISL Data sheet, ISL manual, ISL pdf, ISL, datenblatt, Electronics ISL, alldatasheet, free, datasheet. Renesas Electronics ISL are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Renesas Electronics ISL
|Published (Last):||6 June 2009|
|PDF File Size:||2.20 Mb|
|ePub File Size:||12.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
Bypass LDO output with a minimum of 4. Does not apply in PFM mode see further details on page The actual capacitance value required relates to the physical size needed to achieve low ESR, datasjeet well as to the chemistry of the capacitor technology.
Supply Controllers for Notebook. The ISL includes on-board datadheet sequencing, the power-good POK outputs, digital soft-start, and internal soft-stop output discharge that prevents negative voltages on shutdown.
Other features include pulse skipping, which maximizes efficiency in light-load applications, and fixed-frequency PWM mode, which reduces RF interference in sensitive applications.
Leave open if there is no load. Choose R2 to be approximately 10k and solve for R1 using Equation 6.
The boost capacitance should be as large as possible to prevent it from charging to excessive voltage, but small enough to adequately charge during the minimum low-side MOSFET conduction time, which happens at maximum operating duty cycle this occurs at minimum input voltage. A current source, as shown in Figure Limits established by characterization and are not production tested.
The output capacitance must also be high enough to absorb the inductor energy while transitioning from full-load to no-load conditions without tripping the overvoltage fault latch. In an adjustable mode, the LDO output can be set from 0.
The ISL includes on-board power-up sequencing, the power-good POK outputs, digital ratasheet, and internal soft-stop output discharge dstasheet prevents negative voltages on shutdown. The synchronous-switch gate drivers are directly powered from PVCC, while the high-side switch gate drivers are indirectly powered from PVCC through an external capacitor and an internal Schottky diode boost circuit.
The ON-time one-shot triggers when the iwl6236 conditions are datashret ON-times translate only roughly to switching frequencies. Lower input voltages result in better efficiency. Datashee to the SMPS1 output. The rectifier is a clamp across the synchronous rectifier that catches the negative inductor swing during the dead time between turning the high-side MOSFET off and the synchronous rectifier on.
LDO can provide a total of mA external loads. The internal digital soft-start timer begins to ramp up the maximum-allowed current limit during start-up. This choice determines the basic trade-off between size and efficiency.
When combined with the undervoltage-protection circuit, this current-limit method is effective in almost every circumstance.
Copyright Intersil Americas Inc. When the LDO is set at 3.
As h approaches 1, the absolute minimum dropout point, the inductor current is less able to increase during each switching cycle and VSAG greatly increases unless additional output capacitance is used.
This practice is essential for stable, jitter-free operation. Ignoring the sag due to finite capacitance: A constant ON-time PWM control scheme operates without sense resistors and provides ns response to load transients while maintaining a relatively constant switching datashheet.
UVP is ignored for at least 20ms datasgeetafter start-up or after a rising edge on EN. When the ON-time has expired, the controller re-enables the low-side MOSFET until the controller detects that the inductor current dropped below the zero-crossing threshold.
C8 voltage is equal to OUT1 minus a diode drop. Run the power plane ground currents on the top side only, if possible.
High-Efficiency, Quad-Output, Main Power Supply Controllers For Notebook Computers
All Rights Reserved All other trademarks mentioned are dataeheet property of their respective owners. This device features a linear regulator providing 3. The MOSFETs incorporate a high-speed silicon body diode as an adequate clamp diode if efficiency is not of primary importance.
For a given value of h, the minimum operating voltage can be calculated as: Output voltage control for SMPS2. The actual peak current is greater than the current-limit threshold by an amount equal to the inductor ripple current. Once the output is within regulation, the controller will operate as normal.
The configuration of the pin 1 identifier is optional, but must be located within the zone indicated. All internal circuitry shuts down during thermal shutdown. The ISL dual switching regulator operates at different frequencies.
ISL Datasheet, PDF – Alldatasheet
Wide Input Voltage Range 5. Also, keep in mind that transient-response performance of buck regulators operated close to dropout is poor, and bulk output capacitance must often be added see Equation 11 on page Intersil Electronic Components Datasheet. An optional external charge. This interleaves the current pulses drawn by the two switches and reduces the overlap time where they add together.