DANFOSS EKC 102 PDF

EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . Temperature controller. EKC MAKING MODERN LIVING POSSIBLE Sensors: Danfoss Pt, PTC or NTC • Calibration of sensors. RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D.

Author: Nakora Moogujin
Country: Belarus
Language: English (Spanish)
Genre: Science
Published (Last): 11 July 2007
Pages: 281
PDF File Size: 6.83 Mb
ePub File Size: 6.88 Mb
ISBN: 227-7-95308-867-8
Downloads: 94216
Price: Free* [*Free Regsitration Required]
Uploader: Akinole

If the defrost sensor registers a higher temperature than the one set here, the fans will be stopped. I want to receive an additional SMS with a notification Your phone number: Thermostatic Expansion Valves flow direction: Time delay for door alarm The time delay is set in minutes.

A-model for simple regulation B-model where an alarm function and possibly also a digital input will be required Danofss where the defrost temperature also enjoys top priority D-model with fan function, change-over between temperature reference and case cleaning function All these four controllers are without data communication. Push the middle button until the parameter value is shown 4.

The sensor is placed in the cold air flow after the evaporator or in the warm air flow just before the evaporator. Set password Ek setting If you need to return to the factory-set values, it can be done in this way: If not, you can cancel the function with setting 0.

When gas defrosting the compressor relay will be cut in during defrost.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102D 084B8506 for Freezer

Copying was not correct. Activation of reference displacement When the function is changed to ON the thermostat differential will be increased by the value in r When the compressor is operating it danfose run for at least x minutes.

  INTEL DESKTOP BOARD D915GAV D915PGN PDF

The input is not used 1 Door function. Lower alarm limit Here you set when the alarm for low temperature is to start. The Danfoss controller is used for applications where temperature is critical. Defrost method Here you set whether defrost is to be accomplished with electricity, natural or “non”.

To avoid a too high setting of the setpoint, the max. Activation can take place via r39 or input DI Alarm The controller can give 1022 in different situations. The relay cuts in when lower temperatures are required. After paying for this item you will be awarded: The function will be active after each and every power failure. If the function is used, access code 1 o05 must also be used.

Sensor error on 120 E The alarm danofss not become active until the set time delay has been passed.

When the value is passed, a defrost will start. Communication error and timeout Regulation is carried out when the input is short-circuited, and regulation is stopped when the input is put in pos. If this description is not sufficient, please send us a question to this product. Sensor error on Sair E A special moulding technique unites the hard front plastic, the softer buttons and the seal, so that they become an integral part of the front panel.

Between two defrosts the S5 temperature will become lower the more the evaporator ices up the compressor operates for a longer time and pulls the S5 temperature further down.

The controller controls the defrost with either natural defrost or electric defrost. Instead of the compressor a solenoid valve may of course be connected in the liquid line. We also inform you that: When two compressors are cut in and out the two relays will operate in opposite directions. Copying concluded and OK 4: Via three pushes on a switch you change from one phase to the next phase.

  BIBLIA DE ESTUDIO RYRIE PDF

None, no sensor is connected 1: When the input is open it signals that the door is open.

To avoid a too low setting of the setpoint, the min. Notify me about a product availability. You obtain this by pushing the upper button for a couple of seconds – you will then enter the column with parameter codes. A measurement of the defrost temperature can be obtained directly through the use of an S5 sensor.

This function can only be used in 1: None, defrost is based on time EKC A: This happens when the temperature reaches the upper part of the differential. Defrosting S20 Emergency cooling S25 Manual control of outputs S32 Delay of output at start-up non The defrost temperature cannot be displayed.

EKC B Controller with two relay outputs, extra temperature sensor and digital input.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC D B for Freezer

If the Compressor in operation is unable to lower the temperature to the cutout point, the other compressor will be cut in again.

A-alarms will not become visible until the set time delay has expired.

Relay output 2 can be used for alarm function or for cutin and cutout of a refrigeration step 2. This page uses cookie files to provide its services in accordance to Cookies Usage Policy. Contact details entered above are not used to send newsletters or other advertisements. Here you set how large a slide of the S5 temperature can be allowed.