All OMRON products are capitalized in this manual. The word .. purpose and a comparison between the CQM1H and the CQM1. Section 2. 1. V4+. Voltage pin, input 4. 2. V Common pin, input 4. 3. V3+. Voltage pin, input 3. 4. V Common pin, input 3. 5. V2+. Voltage pin, input 2. 6. V Common . View and Download Omron CQM1 operation manual online. Programmable Controllers. CQM1 Controller pdf manual download. Also for: Sysmac cqm1.

Author: Jurg Talkree
Country: Maldives
Language: English (Spanish)
Genre: Science
Published (Last): 21 September 2017
Pages: 99
PDF File Size: 3.42 Mb
ePub File Size: 3.27 Mb
ISBN: 368-7-78732-698-8
Downloads: 21843
Price: Free* [*Free Regsitration Required]
Uploader: Mikajind

Additions and changes made to application precautions. If the CQM1 is not turned on, turn it on for at maunal one minute and then turn it off.

Press the DEL Key. Programmable Controller Power Interruptions CPU Unit Section removed will not be fully charged and memory may be lost before the new battery is inserted. Pages xvii and xviii: When the Unit is in measurement mode, the cqj1 scaled conver- sion data is stored in the input word allocated to the Unit.

Mmanual If the Analog Input Unit malfunctions due to external noise through the power line to the Analog Input Unit, insert a noise filter to the power line. Scaling The conversion of a value in a certain range to an output voltage or current in a certain range is called scaling. Page OFF if this nanual occurs. Glossary Glossary Indirectly addressed DM area.

Terminals B and B also short-circuited internally. Section Wiring 4.

Note The allowable voltage ranges for the CQM1 are as follows. Any other indicator display indicates an error. C Autotuning executed for loop 2 after RUN started.


The status of bits and contents of xqm1 being monitored can also be controlled. Page —10 and 55 C tested at 23 C Vibration resistance Destruction: When two Expansion Masters are used, set one as Unit 1 and the other as Unit 2. When the axes agree, the indicator on the light projection fiber head will be lit.


Press the Up Arrow Key to delete the specified instruction. Wiring and Assembly The following illustrations show the procedure for wiring mamual assembly of solder- type connectors.

OMRON CQM1 Operation Manual

nanual OK reading only OK reading only Be sure to change function code assignments before inputting the program. Indicator Alarm Table The table below shows the description and remedy of an error occurring in the G Interface Unit. Output points correspond physically to terminals or connector pins. M3 Optimum tightening torque: Thermocouple type and range setting for loops 1 and CMP 20 Set point reception checked.

About This Manual Please read this manual carefully and be sure you understand the information provide before attempting to install and operate the CQM1. Page Note Insert the fiber in the direction indicated by the arrow. The input process time varies with the timing hold currently selected.

When zero input is turned ON while the Unit is sampling data, the scaled con- version data will be shifted to zero and stored as binary data in the input word, manial the comparison result flags of the input word are turned ON or OFF accord- ing to the comparison result processed by the Unit. The width varies with the Power Sup- ply Unit, as indicated. Iotc or later. An error will result if pins 1 to 8 are all set to OFF i. If both input and output are set to 2 words 32 manuxlup to eight Input Units and eight Output Units can be connected, if 4-point Slaves are used.


Mwnual to display the execution status of the specified program section.

Don’t show me this message again. Page Glossary unsigned binary A binary value that is stored in memory without any indication of manua it is positive or negative.

Press the CHG Key to begin 3-word data modification. Note Mannual not pull the power supply cable, or the power supply cable may be broken or connector may be disconnected. Technical specifications of the Units are also provided. Nomenclature And Settings Nomenclature Section Commands and Responses E Operation Transmission Delay Time If stable detection of objects is not possible after teaching, try teaching Page Timing signal The Unit requires time to process input and to set data to mabual input word corresponding to the input.

Application Precautions Application Precautions! Monitor the status of the desired word according to the procedure described in Bit, Digit, Word Monitor. Don’t have an account? It is not necessary to input leading zeroes. Timing Hold Unit continues sampling. Measurement Mode or Comparison Mode: These compo- nents lock together at the sides, allowing simple changes in the size and capac- ity of the PC.

Section Commands and Responses Response If the output word is set vqm1 the correct command code, the sign of the scaling value and the scaling value will be set to the cq,1 word alternately in the fol- lowing format. Cylindrical Sensors Use the following tightening torque when attaching a sensor with a set screw: