ACCULOAD III MANUAL PDF

Smith Meter® AccuLoad and AccuLoad III are trademarks of FMC The default or operating values used in this manual and in the program of the AccuLoad III. AccuLoad III High Speed Prover Output · AccuLoad III Vapor Recovery Application Bulletin · AccuLoad IIInet Application Manual · AccuLoad III-S N4 Hardware. The default or operating values used in this manual and in the program of the Smith Table of Contents iii. Volume Accuracy – Preset Amount Type.

Author: Samushakar Arashit
Country: Montserrat
Language: English (Spanish)
Genre: Career
Published (Last): 27 December 2012
Pages: 397
PDF File Size: 3.9 Mb
ePub File Size: 7.1 Mb
ISBN: 778-8-51353-317-7
Downloads: 1950
Price: Free* [*Free Regsitration Required]
Uploader: Kajiran

The table above indicates default operation. For purposes of determining valid accu,oad combinations, a side-stream blending arm can be considered a two-product ratio blending arm, as both require the same resources. Don’t show me this message again. The AccuLoad controls the flow of the additive in an attempt to constantly maintain the desired ratio as if the additive were a ratio product.

Smith Meter AccuLoad III – PDF

The ratio of varying products is designated in the recipe as a percentage of the qccuload preset. The F1 key may be used from the dynamic displays to change the focus to the other arm, which allows the START key to begin the batch on the other load arm.

Remove all items from the box and make sure the. Additive Monitoring Additive injector feedback provides the capability of the AccuLoad monitoring the additive products that are being injected. Implementing this feature requires that a load arm be identified as unloading ; up to six load arms can be so configured.

The operation described in this section assumes that the AccuLoad is being operated locally through the keypad. Auto injectors, where the additive outputs that are programmed in the AccuLoad III will automatically be selected for each batch according to the programming in the recipe definition; Ii injectors, where the operator is prompted at the beginning of each transaction; Manual injectors, where the operator is prompted at the beginning of each batch.

  HARTMANN PRODUKTKATALOG PDF

Comments to this Manuals Your Name.

Alarm options are also available with this feature. Another meter and control valve is located downstream from where the two products merge. To make this website work, we log user data and share it with processors.

Remove the seven barrier screws and barrier plate Figure 1 from the KDC. Note that only those factors currently programmed will be offered as selections.

A table of possible configuration combinations appears below. Additive injection, pump control, alarm control, set stop, valve control, back pressure control, automatic adjustment of final trip point, and flow rate controlled injector. Should the valve fail to close within a programmable period after having been signaled, a contact is msnual.

An exception to this rule is when another delivery of the same product is specified in the recipe. Optional Remote IP Access. The NeXpose Scan More information. Ratio Blending Ratio blending is the process of mixing multiple products simultaneously during delivery to a vessel e.

Smith Meter AccuLoad III

These jumper states are available via communications. Using the interface More information. If at any time an alarm occurs while in the Ready State or the Run Mode, the AccuLoad III will attempt to shut down the flow and a message indicating an alarm condition will pop up over the current display. Startup Guide Honeywell, Inc. Each arm may be configured to deliver acxuload unload a straight product, or may be configured as a sequential or ratio blender.

The AccuLoad can also pass card data and status to a host computer. The AccuLoad III can control six meters, so if ratio blending is selected on any arm, the number of additional load arms available depends on the number of products to be delivered simultaneously by the ratio blending arm s. Average Meter Factor g Continue Save Note that zoom of the top display remains full screen. Environmental fluctuations within specified limits have virtually no effect on the operation of this control system.

  DLG 267 00 AGGIORNATO PDF

Should flow rate variations occur, the profile is dynamically adjusted to attain the best possible mix. Straight product arms must be programmed for one product.

The AccuLoad III will monitor and totalize the volume of additive injected by piston-type additive injectors or smart injectors. Using the up and down arrow keys, the display will read as follows: The AccuLoad controls a metered injector for proving, and then calculates acuload new meter factor for the metered cacuload. UL Listed and Classified More information. For ratio blending with manusl product per meter, a mankal of six components may be blended together.

Press up or down arrows to select injector. In addition, ESD controls should be employed to avoid damaging mnaual electronic com.

Connecting wifi module on shield: It is configurable to support a variety of user applications. Arduino Wifi shield And reciever.

404 page not found

If low flow start is not desired, enter zero. Retrieve all configuration information and data logs as detailed above using the AccuMate program, see. Remove all items from the box and make sure the More information. Enter the batch amount desired.